Close Window  X 
swatch
Color rings are not available. Colors on computer monitors will vary widely due to the type of monitor and the graphics card. We do not guarantee colors shown on this website will match actual product.
Close Window  X 
Close Window  X 
Help shows here when images are moused over
Sign Letter Source .com Manufacturer & Distributor since 1999 Products ship from various locations including Virginia-Minnesota-Iowa-Texas-Montana and Nevada
cart Shopping Cart:   $0.00
Contact Us
brass sign letters
  • Ordering Page
  • Price Chart
  • Mounts
helpStep 1 helpStep 2 helpStep 3 helpStep 4 helpStep 5
Enter Letters - Numbers - Punctuation Material
Thickness
Uppercase Height Inch + Fraction Choose Finish Choose a Style/Font
Line 1
+
arrow
Line 2
+
arrow
Line 3
+
arrow
Line 4
+
arrow
Show tooltip help
When ordering numbers, if they are all the same size, finish, font, just type them all into line 1 eg: 123456789101112
INFO Letter Depth Uppercase Price Lowercase Price Line Total Pattern Price Total Price GRAND TOTAL
Line 1           $0.00 $0.00
help Alignment help Backgrounds (design use only) Update Display Automatically
Displays your letters in the chosen font
1" Letters or Numbers are restricted to BLOCK fonts only
Step 6:Select Mounting Hardware
  helpBasic Hardware helpStud Length helpStand Off helpStud for Brick helpMounting Pattern
Line 1
arrow
Line 2
arrow
Line 3
arrow
Line 4
arrow
Total Characters  
Cart Subtotal
Total Cost for Characters  
Mounting Pattern  
Total this page  
Qty
*Quantity is applied to ALL lines
Holding space for price table

Installation Hardware

No Mounts Mount with small spots of silicon adhesive directly to a flat dry surface. This option can be a bit messy and care must be taken to ensure that silicon doesn't squeeze out from the sides. Pinhead amounts should be used, dotted around the back surface in strategic locations. Masking tape will be needed to hold the letters in place while the silicon dries. A good alternative is to use some double stick tape in places that will do the initial holding while the silicon sets.
Keyhole Mount Not many companies offer this but its an excellent way to mount letters indoors where you may later want to remove them for painting the wall or to relocate. With this mount and a mounting pattern, all you do is run drywall screws into the wall, deep enough so their heads protrude, then locate the heads over the large keyhole opening, push toward the wall and pull down to lock in place. No drilling, no glue, and easily removable for painting or moving. Requires fonts large enough and thick enough to accommodate the depth of the keyhole and the
size of its opening. Usually 6" and above and 3/8" or more thick.
Double Side Tape Mount High quality, 3M brand Very High Bond double sided tape makes mounting a breeze. Can be used inside or outside on smooth surfaces. Recommended for non porous and sealed surfaces. Metal to metal has strong adhesion.
Welded Stud

On thinner letters up to 1/4" thick, we have to weld threaded studs.These studs are not removable without a lot of trouble. Mounting this type of letter requires drilling the wall or mounting surface to accept the metal studs.

 

Drill and Tap On thicker letters, 3/8" and 1/2", we can drill and tap the backs of the letters to accept the threaded rods (studs). A mounting pattern is highly recommended to locate the correct places to drill. Once the holes are drilled, screw studs into the stud blocks being careful not to over tighten, then fill the holes with silicon caulk, coat the studs and push the assembly into the wall up to where the stud block meets the wall surface.
Bottom Stud Bottom studs are available on 3/8" and 1/2" thick letters over 4" tall. For letters over 8" in height, some form of tie backs will be required to mount this outside. Pleaase check with your local city ordinence before purchasing.
Bottom Rail Similar to a bottom stud, the rail mount includes a length (8ft max) of "C" channel aluminum that tie all your letters together on a single line. Restrictions still apply for tie backs on letters over 8" tall in outdoor use.
Double Rail Double sets of rails can be used to span spaces or for uneven surfaces such as corrugated buildings. We provide rails and bolts, max. 8ft. Extra costs apply.

CONTACT  | ABOUT US  |  ORDER STATUS   |   SHOPPING CART   |  INSTALLATION INSTRUCTIONS  |  HOME
COPYRIGHT © 2010 MONTANA LETTERING INC.      PRIVACY NOTICE

 

instructional video