- Ordering Page
- Colors/Finishes
- Fonts
- Price Chart
- Mounts
- Gallery
- About
| Aluminum Finishes |
| Dime represents the level of reflectivity in the finish |
 |
 |
| 1333 Satin Brushed |
1133 Polished |
 |
 |
| 3222 Clear Anodized |
3258 Satin Gold Anodized |
 |
 |
| 4312 Medium Bronze Anodized |
4313 Dark Bronze Anodized |
 |
 |
| 3204 Black Anodized |
7222 Polished Clear Anodized |
 |
 |
| 7258 Polished Gold Anodized |
7312 Polished Medium Bronze Anodized |
 |
 |
| 7313 Polished Dark Bronze Anodized |
7204 Polished Black Anodized |
|
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
| Most Custom fonts can be cut at no extra charge |
Holding space for price table |
Installation Hardware
 |
Mount with small spots of silicon adhesive directly to a flat dry surface. This option can be a bit messy and care must be taken to ensure that silicon doesn't squeeze out from the sides. Pinhead amounts should be used, dotted around the back surface in strategic locations. Masking tape will be needed to hold the letters in place while the silicon dries. A good alternative is to use some double stick tape in places that will do the initial holding while the silicon sets. |
 |
Not many companies offer this but its an excellent way to mount letters indoors where you may later want to remove them for painting the wall or to relocate. With this mount and a mounting pattern, all you do is run drywall screws into the wall, deep enough so their heads protrude, then locate the heads over the large keyhole opening, push toward the wall and pull down to lock in place. No drilling, no glue, and easily removable for painting or moving. Requires fonts large enough and thick enough to accommodate the depth of the keyhole and the
size of its opening. Usually 6" and above and 3/8" or more thick. |
 |
High quality, 3M brand Very High Bond double sided tape makes mounting a breeze. Can be used inside or outside on smooth surfaces. Recommended for non porous and sealed surfaces. Metal to metal has strong adhesion. |
 |
On thinner letters up to 1/4" thick, we have to weld threaded studs.These studs are not removable without a lot of trouble. Mounting this type of letter requires drilling the wall or mounting surface to accept the metal studs.
|
 |
On thicker letters, 3/8" and 1/2", we can drill and tap the backs of the letters to accept the threaded rods (studs). A mounting pattern is highly recommended to locate the correct places to drill. Once the holes are drilled, screw studs into the stud blocks being careful not to over tighten, then fill the holes with silicon caulk, coat the studs and push the assembly into the wall up to where the stud block meets the wall surface. |
 |
Bottom studs are available on 3/8" and 1/2" thick letters over 4" tall. For letters over 8" in height, some form of tie backs will be required to mount this outside. Pleaase check with your local city ordinence before purchasing. |
 |
Similar to a bottom stud, the rail mount includes a length (8ft max) of "C" channel aluminum that tie all your letters together on a single line. Restrictions still apply for tie backs on letters over 8" tall in outdoor use. |
 |
Double sets of rails can be used to span spaces or for uneven surfaces such as corrugated buildings. We provide rails and bolts, max. 8ft. Extra costs apply. |
| Cut Metal Letters |
|
Flat cut out metal letters are made from various thicknesses of sheet aluminum, brass, bronze, copper, stainless steel and black steel. Cut with computer driven router systems, we can reproduce all sorts of designs, logo's and virtually any font or custom shape you can think of. We can cut letters as small as 1" high to 30" tall in thicknesses ranging from 1/8" to 1/2".
It doesn't stop there though. All of our letters and logos can be Brushed Satin, polished or painted to meet your specifications and to give you just the look you need for your project or sign.
We can take your .EPS, .CDR or other vector-based art files and produce your letters and logos in just 7 days. Durable enough for outdoors, yet perfect enough for any boardroom application |
All of our finished letters are fully protected against weathering with a UV protectant clearcoat so that your sign will look as good after years of service, as it did the day it arrived.
Custom painted colors are also available using PMS matching or using a manufactures color such as Sherwin Williams, PPG, etc. |
Custom painted 3/8" aluminum inset for "A" Logo with painted "ALABAMA GOLF" and smaller black painted letters over certificate plaques. |
|
|
